[QuadList] VR-1200B Daily Servo Set UP

[dcfwtx at aol.com]

 In the mid 60's, CBS and NBC had individual modifications to the VR 2000 that they frequently shared. CBS was notorious for modifying just about everything when it came into the door. Many of these mods were incorporated into later production models, such as the VR 2000Bs.

David Crosthwait
www.dcvideo.com


 


 

-----Original Message-----
From: Guy Spiller <quadruplex at verizon.net>
To: Quad List <quadlist at quadvideotapegroup.com>
Sent: Sun, Aug 23, 2009 10:45 am
Subject: Re: [QuadList] VR-1200B Daily Servo Set UP









Wow, does this bring back memories...even though I was 19 at the time.?

I think my knees are starting to hurt again after seeing this!  LOL?

Guy?
?

Chill315 at aol.com wrote:?

> We had this on a 5 by 7 card that was taped inside the door below the 
> monitor on the sidecar.  It worked  and we had very few problems.  
> Thought that I would pass it on.?

>  
> Chris Hill?

>  
>  
>  
> VR-1200 B Series Inter-Sync Systems Daily Set Up?

>  
> PRIOR TO ANY ADJUSTMENT, LET HEAD SPIN FOR ABOUT 30 MINUTES?

>  
> Do in the following order?

>  
> Reference Discriminator?

>  With head spinning, adjust R28 on board 2 for zero.?

>  
> Drum Oscillator?

>  
>  With head stopped, adjust Drum oscillator R21 on board 6 for stable 
> wave form.?

>  
> Tach Discriminator?

>  
>  With Drum spinning, set R85 on board 6 for zero?

>  
> Capstan Oscillator?

>  
>  Set Capstan Oscillator for steady wave form?

>  
> Capstan Discriminator?

>  
>  With Machine in Record, set R1 on board 12 for zero?

>  
> Drum Tach position?

>  
>  With Machine in Record, verify that tach is at correct position on 
> demod using pulse cross.?

>  
>?

> If doing editing,?

>  
> Turn Editor on?

>  
>  Set H Phase to zero with input that you are using when source is timed?

>  
>  Set Tach Phase to same position as was used in RECORD mode?

>  
>  Note: If original tape was as recorded with incorrect Tach phase, set 
> Tach phase to match the incorrect tape. 
>  
> H phase sets quality of in-going edit and Tach Phase sets quality of 
> out going edit.  Do a test edit if desired and check AMTEC error for 
> quality of edits.?

>?

> ------------------------------------------------------------------------?

> ------------------------------------------------------------------------?

>?

> _______________________________________________?

> Please trim posts to relevant info when replying!?

> Send QuadList list posts to QuadList at quadvideotapegroup.com?

> Your subscribe, unsubscribe and digest options are here:?

> http://mail.quadvideotapegroup.com/mailman/listinfo/quadlist_quadvideotapegroup.com?

> ------------------------------------------------------------------------?

>?

>?

> No virus found in this incoming message.?

> Checked by AVG - www.avg.com 
> Version: 8.5.392 / Virus Database: 270.13.64/2320 - Release Date: 08/22/09 18:04:00?

>?

>   ?

-- 
Guy Spiller?

email: quadruplex at verizon.net?

phone: (804) 379-2050?

website: www.GuySpiller.com?

Midlothian, VA?
?


_______________________________________________?

Please trim posts to relevant info when replying!?

Send QuadList list posts to QuadList at quadvideotapegroup.com?

Your subscribe, unsubscribe and digest options are here:?

http://mail.quadvideotapegroup.com/mailman/listinfo/quadlist_quadvideotapegroup.com?



 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://quadvideotapegroup.com/pipermail/quadlist_quadvideotapegroup.com/attachments/20090823/a524a9fe/attachment-0005.html>